Hambid for Ham radio, scanners, DAB, Shortwave & CB radios

sales@radioworld.co.ukResponse in 24 hours
Trustpilot
01922 414 796

Monday - Friday: 9:00am - 5:00pm

Saturday: 9:30am - 4:00pm

My basket: £0.00
0
Wishlist
wimo radio products
PMM 10/2.9 Pneumatic Telescopic Mast 10m
wimo radio products
PMM 10/2.9 Pneumatic Telescopic Mast 10m
£2,900.00 (£2,416.67 exc. VAT)
Download a PDF document for PMM 10/2.9 Pneumatic Telescopic Mast 10m
View video
Fast UK
delivery
Worldwide
delivery
Add to wishlist
Product code:38300
Brand:wimo radio products

Fast raising and lowering, comfortable Masts for antennas and other payloads (e.g. Floodlights, Cameras, Anemometer, Microphones etc.).

These masts are made of concentric sections of anodized aluminium, equipped with a lock against rotation. The top section is terminated with a large flange which allows installation of various payloads. The fucntional principle is the reverse of an air pump for your bicycle: if you put pressurised air into the nozzle of the pump, the handle extends due to the internal pressure.

The compressor required to extend the mast is not included in shipment; but you can use any other existing compressor our source of pressurized air as well (e.g. the pressurized air of a truck brake).

The mast is operated (extended or lowered) by a three-position valve: Raise/Hold/Lower.

When one section of the mast is fully extended it locks into the next section. This locking ensures that the mast is held extended even when the pressurised air is removed. The mast can even be locked in different heights by not extending all sections. To lower the mast just pull the release handle on the lowest section, the uppersections will lower themselves gently. Then pull the handle of the next section ow in reach, lower this, and so on...

For installation on level surfaces the mast comes equipped with a solid tripod. This tripod allows adjustments for slopes with some inclination. This tripod must be fixed to ground, even for masts marked as "self supporting, no guying required". Alternatively mast clamps for installation on a wall or vehicle are available.

Currently we offer two different models.

The lighter model is intended to be used with guy wires. The max. allowed wind load cannot be specified on this model, because that's depending on the type of guying.

Static calculations for wind zones 1 and 3 are available for the PMM10/2.9, see below.

The table details the PMM10/2.9 apply for free-standing operation, with the mast with the antenna surface and 120km/h calculated approximately 66cm bends. Therefore it is recommended also to guy the mast, and of course the antenna surface can be enlarged when operating with guying wires. When the center of the antenna surface is in the amount of the guying point so that no torque is exerted by the wind, the maximum antenna surface would be theoretically infinite. But please do not overload, because the mast otherwise be bulgy and can break, especially when the bias of the guying wires are to strong. Because the force applied by the guying tension is indeed in relation to the tension angle as a compressive force in the mast!

PMM 10/2.9 PMM 9/2.8

self supporting with guying

Length extended 10 9 m

Length retracted 2.86 2.76 m

Weight 77 37 Kg

Payload weight max 100 30 Kg

Max. Antenna surface

not guyed 1.18 @ 90km/h

0.53 @ 120km/h see text m²

Number of sections 5 5

Diameter lowermost tube 160 98 mm

Diameter uppermost tube 82 36 mm

Length of tripod beam (Radius)

ca. 152 ca. 152 cm

Order No. 38300 38310

Reviews