Hambid for Ham radio, scanners, DAB, Shortwave & CB radios

sales@radioworld.co.ukResponse in 24 hours
01922 414 796

Monday - Friday: 9:00am - 5:00pm

Saturday: 9:30am - 2:00pm

My basket: £0.00
ANAN-7000DLE MKII 100W HF & 6M Transceiver (No Embedded PC)
ANAN-7000DLE MKII 100W HF & 6M Transceiver (No Embedded PC) s1
ANAN-7000DLE MKII 100W HF & 6M Transceiver (No Embedded PC)
£2,899.96 (£2,416.63 exc. VAT)
Download a PDF document for ANAN-7000DLE MKII 100W HF & 6M Transceiver (No Embedded PC)
Fast UK
Add to wishlist
Product code:ANAN-7000DLE MKII

The ANAN-7000DLE – Second to none!

Using Direct Down Conversion with an ultra low phase noise clock yields an RMDR of 116dB @ 2Khz separation, this means that close in weak signals will not be masked by the receiver’s phase noise.

The transmitter specifications are also off the chart, use of a new 16bit DAC with an ultra low noise clock source results in transmit phase noise better than any other product available in the market.

Use of LDMOS drivers and an optimized final Amplifier stage with adaptive Predistortion Algorithm (PureSignal) yields transmit IMD of -68db @ 100W PEP, this is at least 20dB better than any Class A transmitter and over 30dB better than the competition.

Use of two 16bit phase synchronous ADCs allow for advanced applications such as Diversity reception for ultimate noise mitigation and effects of signal fading.

The ANAN-7000DLE HF & 6M 100W SDR Transceiver offers top of the line performance is a compact rugged package, it is based on the work of the OpenHPSDR community.


Stainless steel chassis and large aluminium heatsink for excellent thermal dissipation and Rx/Tx isolation.

PA board improvements for higher duty cycle, 100% ICAS duty cycle supported.

Tx Signal generation redesigned to improve SNR at low power levels.

General Specifications:

Architecture: Direct Sampling DDC/DUC Transceiver

Interface: Ethernet

Phase Noise (Clock): -149dB @ 10Khz

TCXO Stability (Typical): /- .1 PPM

Modes: CW, SSB, NFM, AM, Digital

Antenna Ports: Three BNC 50 ohms Software Configurable Ports, Three BNC ADC1 Bypass and Loop in ports, One BNC for RX2

Frequency Resolution: 1 Hz

Electrical Specifications:

13.8v DC @ 25A, 3A Receive/25A Transmit

Mechanical Specifications:

10Kg (approx. Weight)

Dimensions: 384MM (W) x 114MM (H) x 310MM (D) (Not including extrusions)

Rugged Steel Chassis and Aluminum heatsink with Temperature controlled internal/External (Optional) Fan.

Receiver Specifications:

Receiver Architecture: Direct Down Conversion

Dual 16 bit Phase Synchronous ADCs

Independent filter banks for each ADC


Frequency Coverage: 9Khz to 60Mhz

Attenuator: 1-30dB step attenuator

Reciprocal Mixing Dynamic Range (RMDR): 116dB @ 2Khz offset

Receiver Phase noise: -149dB @ 10Khz

Image rejection: 90dB

Hardware support for 7 independent receivers assignable to either ADC

Transmitter Specifications:

Transmitter Architecture: Direct Up Conversion

DAC Resolution: 16 bit

RF Output Power: 100W PEP SSB, FM, RTTY, Digital; 1-30W AM, 100W CW

IMD: IMD3 typically -68dB below PEP @ 100W output on 20M

Harmonics: Typically better than -43dBc on HF and -60dBc on 6M

Carrier and Opposite Sideband Suppression: Better than -80dBc

Transverter IF Output: 0db to 15dB


RCA Line In, Digital Inputs, PTT in, PTT Out

DB9 Seven Software Configurable Open Collector Outputs

SMA XVTR, 10Mhz reference Input

3.25mm Barrel Mic, CW Key, Headphones and two 6.25mm Speaker Outputs

RJ45 Ethernet LAN Connector